Skip to content
zeveroPublic

About

Arduino Bootloader to Flash from SD Card

Resources

Stars

136 stars

Watchers

18 watching

Forks

Latest commit

 

History

41 Commits

Folders and files

Repository files navigation

avr_boot

SD card bootloader for atmega processors

As easy as it can get! I spent days with this. Hopefully you wont!

  • for any ATMega with 4096kb Bootloader
  • uses Petit FatFs R0.03 for FAT12, FAT16, FAT32
  • looks for FIRMWARE.BIN and flashes it nearly instantly
  • without any interference to your application
  • no CRC Check and no version bytes in EEPROM (see KISS)

Boards Manager installation

avr_boot is integrated in Arduino IDE version 1.6.4 or greater!!! See here for instructions.

Manual installation

This is with avr-gcc and avrdude under linux with an Atmega1284p and AVRISP mkII! Adaption to your case (WinAvr, another Atmega, another flash-tool) will not be complicated...

  • adapt Makefile
    • MCU_TARGET: Your atmegaXXX
    • BOOT_ADR: in bytes not words!
    • F_CPU: CPU Frequency (not critical. A higher value will work as well)
    • SD_CS_PORT: Data Register of the SD CS pin(see the datasheet for your microcontroller)
    • SD_CS_DDR: Data Direction Register of the SD CS pin
    • SD_CS_BIT: Bit of the SD CS pin
    • USE_LED: For debugging 0...deactivate or 1...active
    • USE_UART: For debugging 0...deactivate or divider (UBRR) for baudate see http://wormfood.net/avrbaudcalc.php
  • update spi_pins.h with the SPI pins of your microcontroller if not already defined
  • if using USE_LED adapt LED-pins in asmfunc.S
  • if you want to add FAT12 adapt pff/src/pffconfh.h (default ist FAT16 + FAT32)
  • if you want to support lower case filenames adapt pff/src/pffconfh.h (default is uppercase)
  • if you prefer another filename instead of FIRMWARE.BIN adapt main.c
  • make (you may need to do "sudo apt-get install avr-libc gcc-avr")
  • set fuses: avrdude -c avrispmkII -p m1284p -U hfuse:w:0xda:m
  • flash: avrdude -c avrispmkII -p m1284p -Uflash:w:./avr_boot.hex:i -Ulock:w:0x3F:m

Put your sketch on SD card

  • in Arduino IDE go to File > Preferences and check "Show verbose output during compiliation"
  • compile sketch and find the location of your /tmp/buildxxx/sketch.cpp.hex
  • make bin file: avr-objcopy -I ihex -O binary sketch.cpp.hex FIRMWARE.BIN
  • copy the file into the root of an SD (FAT16/FAT32)
  • put it into the SD slot of your ATmega
  • reset it
  • it might already have happend!

Bootloader sizes

Compiled under linux for atmega328p / atmega1284p

  • 3674 / 3724 bytes
  • 3984 / 4034 bytes debugging with USE_LED
  • 3992 / 4052 bytes debugging with USE_UART

Tested successfully on

  • ATmega168
  • ATmega328P
  • ATmega32u4
  • ATmega1284P
  • ATmega2560 (see issue #2)

Serial support - Help wanted

it should not be impossible to fit a normal serial bootloader (with automatic baudrate detection?) into the remaining bytes ... help is appreciated!

KISS

If you wish you can add CRC Check or versioning with EEPROM but I prefere to keep things simple. avr_boot will reflash your FIRMWARE.BIN as long as it is present. Is this a problem? No! It happens nearly instantly and only differing bytes are flashed really. You may consider putting your logic into your application and perform a CRC Check after the fact to inform the user and delete or rename FIRMWARE.BIN

Thanks to

Alternatives

... call me stupid, but I passed several days debugging those - without success ...

About

Arduino Bootloader to Flash from SD Card

Resources

Stars

136 stars

Watchers

18 watching

Forks

Releases

Packages

Contributors

Languages